收藏本站
MTP23P06V
10
9
QT
30
27
1000
T J = 25 ° C
I D = 23 A
8
7
Q1
Q2
V GS
24
21
100
V DD = 30 V
V GS = 10 V
t r
6
5
18
15
t f
t d(off)
4
3
2
T J = 25 ° C
12
9
6
10
t d(on)
1
Q3
V DS
I D = 23 A
3
0
0
5
10
15
20
25
30
35
0
40
1
1
10
100
Q g , TOTAL GATE CHARGE (nC)
Figure 8. Gate?To?Source and Drain?To?Source
Voltage versus Total Charge
R G , GATE RESISTANCE (OHMS)
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
DRAIN?TO?SOURCE DIODE CHARACTERISTICS
25
T J = 25 ° C
20
15
10
5
V GS = 0 V
0
0
0.25
0.5
0.75
1
1.25
1.5
1.75
2
2.25
2.5
V SD , SOURCE?TO?DRAIN VOLTAGE (VOLTS)
Figure 10. Diode Forward Voltage versus Current
SAFE OPERATING AREA
The Forward Biased Safe Operating Area curves define
the maximum simultaneous drain?to?source voltage and
drain current that a transistor can handle safely when it is
forward biased. Curves are based upon maximum peak
junction temperature and a case temperature (T C ) of 25 ° C.
Peak repetitive pulsed power limits are determined by using
the thermal response data in conjunction with the procedures
discussed in AN569, “Transient Thermal
Resistance?General Data and Its Use.”
Switching between the off?state and the on?state may
traverse any load line provided neither rated peak current
(I DM ) nor rated voltage (V DSS ) is exceeded and the
transition time (t r ,t f ) do not exceed 10 m s. In addition the total
power averaged over a complete switching cycle must not
exceed (T J(MAX) ? T C )/(R q JC ).
A Power MOSFET designated E?FET can be safely used
reliable operation, the stored energy from circuit inductance
dissipated in the transistor while in avalanche must be less
than the rated limit and adjusted for operating conditions
differing from those specified. Although industry practice is
to rate in terms of energy, avalanche energy capability is not
a constant. The energy rating decreases non?linearly with an
increase of peak current in avalanche and peak junction
temperature.
Although many E?FETs can withstand the stress of
drain?to?source avalanche at currents up to rated pulsed
current (I DM ), the energy rating is specified at rated
continuous current (I D ), in accordance with industry
custom. The energy rating must be derated for temperature
as shown in the accompanying graph (Figure 12). Maximum
energy at currents below rated continuous I D can safely be
assumed to equal the values indicated.
in switching circuits with unclamped inductive loads. For
http://onsemi.com
5
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MTP2955V MOSFET P-CH 60V 12A TO-220AB
MTP2P50E MOSFET P-CH 500V 2A TO-220AB
MTP3055VL MOSFET N-CH 60V 12A TO-220AB
MTP3055VL MOSFET N-CH 60V 12A TO-220
MTP3055V MOSFET N-CH 60V 12A TO-220AB
MTP36N06V MOSFET N-CH 60V 32A TO-220AB
MTP50P03HDL MOSFET P-CH 30V 50A TO-220AB
MTPD1346-010 PIN DIODE 1300NM FLAT 2.8MM TO46
相关代理商/技术参数
MTP24K11 功能描述:插线板 1DC PANEL 11 UNWIR RoHS:否 制造商:Switchcraft 产品类型:Bantam (TT) 正规化: 高度/机架数量: 深度: 端接类型: 位置/触点数量:48
MTP24K11B 功能描述:插线板 IDC PANEL 11 WIRED RoHS:否 制造商:Switchcraft 产品类型:Bantam (TT) 正规化: 高度/机架数量: 深度: 端接类型: 位置/触点数量:48
MTP24K7 功能描述:插线板 7 X 6 UNWRD IDC WA RoHS:否 制造商:Switchcraft 产品类型:Bantam (TT) 正规化: 高度/机架数量: 深度: 端接类型: 位置/触点数量:48
MTP2603G6 制造商:CYSTEKEC 制造商全称:Cystech Electonics Corp. 功能描述:P-CHANNEL ENHANCEMENT MODE POWER MOSFET
MTP2603N6 制造商:CYSTEKEC 制造商全称:Cystech Electonics Corp. 功能描述:P-CHANNEL ENHANCEMENT MODE POWER MOSFET
MTP2603Q6 制造商:CYSTEKEC 制造商全称:Cystech Electonics Corp. 功能描述:P-CHANNEL ENHANCEMENT MODE POWER MOSFET
MTP27N06L 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:ON Semiconductor 功能描述:
MTP27N10E 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:TMOS POWER FET 27 AMPERES 100 VOLTS RDS(on) = 0.07 OHM